| CRCChecking
|
Specifies the credentials and security properties.
The valid values are as follows:
|
None
|
No
|
| CkPtInterval
|
Specifies the checkpoint interval.
The Platform Server checkpoint uses a time interval to determine when to send a checkpoint.
Because checkpoint is time-based, checkpoint always occurs at a regular interval. The checkpoint interval is specified in minutes, and the valid range is
1 to
90 minutes.
|
None
|
No
|
| Command
|
Specifies the command running on the destination server. Command format: RCMD|CJ|CP|SJ
- RCMD: remote command
- CJ: CALLJCL
- CP: CALLPGM
- SJ: SUBMIT JOB (for send command only)
|
None
|
No
|
| CommandType
|
Specifies the type of command running on the destination server.
The valid values are as follows:
- Command
- CALLPGM
- CALLJCL
- Submit
- None
|
None
|
No
|
| CompressionFlag
|
Specifies the compression algorithm.
TIBCO MFT Platform Server provides two different compression algorithms:
- Limpel-Zev (LZ)
- Run Length Encoding (RLE)
You can select the algorithm which best suits your network.
The valid values are as follows:
- L: LZ
- N: none
- R: RLE
- U: undefined
|
None
|
No
|
| DataConversionType
|
Specifies the type of data conversion to convert data between ASCII and EBCDIC.
This parameter is used when communicating with systems has defined data structures. This parameter will not be necessary if you are communicating from PC to z/OS.
If you are using TIBCO MFT Platform Server, when you change the
combtlg.dat file, you have to stop and start the Platform Server service for the new conversion table to take effect.
The valid values are as follows:
- B: binary
- E: EBCDIC
- A: ASCII
|
None
|
No
|
| Delimiter
|
Specifies the carriage return line feed control for transferring files.
The valid values are as follows:
|
None
|
No
|
| Department (dpt)
|
Specifies the department associated with the Platform transfer.
|
None
|
No
|
| Description (d)
|
Specifies the 1 to 256 character descriptions of this Platform transfer bank file definition.
If the description contains embedded spaces or special characters, the entire description must be enclosed in double quotation marks (").
|
None
|
Yes
|
| EncryptionFlag
|
Specifies the type of encryption to be used with this transfer.
The valid values are as follows:
- 3D|3DES: 3DES encryption
- BF: blowfish
- BFL: blowfish long
- D|DES: DES encryption
- N: no encryption
- R|RJ|AES: Rijndael
- U: undefined
|
U
|
No
|
| ExpirationDays
|
Specifies the number of days after which the transfer should no longer be attempted.
If this transfer was scheduled, that will take precedence over expiration.
If expiration and retention are used, whichever value occurs first will take precedence.
The valid value range is
0 to
999999.
|
0
|
No
|
| FileWriteMode
|
Specifies the create option for the side writing the file.
The valid values are as follows:
- A: append
- C: create
- CA: create/append
- CR: create/replace
- CRN: create/replace/new
- R: replace
|
C
|
No
|
| InitiatorFileName
|
Specifies the name of the file on the platform that is initiating the transfer.
On a send request, it is the file to be sent. On a receive request, it is where the file will be placed.
|
None
|
Yes
|
| LocalTransTable
|
Specifies the location of the local translation table used with this transfer.
If the path contains embedded spaces, the entire path must be enclosed in double quotation marks (").
|
None
|
No
|
| LoginPWD
|
Specifies the initiating user password.
The password might be up to 64 characters in length and is case sensitive.
|
None
|
No
|
| LoginUID
|
Specifies the initiator user ID used to log in to TIBCO MFT Platform Server.
If this parameter is defined,
TIBCO MFT Command Center will use the user ID and password when connecting to TIBCO MFT Platform Server. If this parameter is not defined,
TIBCO MFT Command Center will search for a server credential that matches the user ID and server definition.
|
None
|
No
|
| PPA1
-
PPA4
|
Specifies the post processing action.
The post processing action allows you to perform up to four actions to be completed by the server when a file transfer request is completed.
The format of the command indicates whether a post processing action should be performed upon success or failure.
The valid values are as follows:
- S|F: success or failure.
- L|R: local or remote.
- CALLPGM: calls a z/OS program with program to program parameter linkage.
This parameter allows the user to call a user program defined on the remote z/OS system.
- CALLJCL: calls a z/OS program with JCL to program parameter linkage.
This parameter allows the user to call a user program defined on the remote z/OS system.
- COMMAND: issues a command at the node specified in the
NodeName parameter.
This is the command that you want to execute on the remote system.
- SUBMIT: submits a job at the node specified in the
NodeName parameter.
This parameter allows the user to submit a job on the remote system. This differs from file to job because the JCL to run actually sits on the remote system.
- ActionData: specifies the data passed to the post action when the conditions specified are met.
|
None
|
No
|
| PServerName
|
Specifies the server name that identifies the initiating TIBCO MFT Platform Server.
|
None
|
Yes
|
| PermittedActions
|
Specifies the Windows-specific file attributes.
These attributes are only valid when sending to a Windows machine.
The valid values are as follows:
- A: archive
- C: NTFS compress
- E: EOF
- H: hidden file
- R: read-only
- S: system file
- Z: control Z EOF
|
None
|
No
|
| PortNum
|
Specifies the IP port on which the remote Platform Server system listens on.
The valid value range is
1025 to
65535.
|
None
|
No
|
| ProcessName
|
Specifies the 8 character field to describe the application which is initiating the transfer.
|
None
|
No
|
| RIPName
|
Specifies the responder IP or host name. Mutually exclusive with
RListName
|
None
|
Yes
|
| RListName
|
Specifies the responder list name. Mutually exclusive with
RIPName.
|
None
|
Yes
|
| RNodeName
|
Specifies the remote node name.
You can define this parameter in place of defining the
RIPName parameter if the remote server is defined in
TIBCO MFT Command Center and you know the server name being used for it.
|
None
|
Yes
Or the
RIPName parameter can be used.
|
| RemoteTransTable
|
Specifies the location of the remote translation table used with this transfer.
If the path contains embedded spaces, the entire path must be enclosed in double quotation marks (").
|
None
|
No
|
| RemoveTrail (rmtrail)
|
Specifies whether to remove trailing spaces from the file.
The valid values are as follows:
|
N
|
No
|
| ResponderFileName
|
Specifies the name of the file on the platform that is responding to the transfer.
On a send request, it is where the file is placed. On a receive request, it is the file to be transferred.
|
None
|
Yes
|
| ResponderPWD
|
Specifies the remote password.
The password might be up to 64 characters in length and is case sensitive.
|
None
|
No
|
| ResponderUID
|
Specifies the user ID that the initiator sends to the responder to gain access to the system.
If this parameter is defined, the Platform Server initiator uses the user ID and password when connecting to the Platform Server responder. If this parameter is not defined, the Platform Server initiator searches for a user profile that matches the user ID and responder node definition. If no user profile is found, the Platform Server initiator sends a trusted user that the Platform Server responder can be configured to accept or reject.
|
None
|
No
|
| RetryInterval
|
Specifies the retry interval. Valid Values between 1-60 (in minutes) (For Unix Only)
|
1
|
Yes
|
| SSLFlag
|
Specifies whether to use secure sockets layer (SSL).
The valid values are as follows:
- Y: Yes
- N: No
- TLS: TLS Tunnel
- D: Default
|
None
|
No
|
| ScanSubDirectory
|
Specifies the sub-directory.
The valid values are as follows:
|
|
|
| SecurityAttribute
|
Specifies the file name that the receiving partner uses as a template for its access control list (ACL).
The ACL is a list that specifies users and groups, and their access permissions on a file.
The ACL of this file is copied to the ACL of the destination file. For this feature to function properly on Windows, the file specified must be readable by the partner which is receiving the file to file transfer and the file being created must reside on an NTFS drive.
|
None
|
No
|
|
StopOnFailure
|
Specifies whether to stop when a transfer can not be added.
The valid values are as follows:
|
None
|
No
|
| ToEmailAddrF
|
Specifies the email address for failed transactions.
|
None
|
No
|
| ToEmailAddrS
|
Specifies the email address for successful transactions.
|
None
|
No
|
| TrScheduleDate
|
Specifies the transfer schedule date.
The valid values are as follows:
- YYYY-MM-DD
- YYYY-MM-DD HH:MM
- YYYY/MM/DD HH:MM
|
None
|
No
|
| TransferDirection
|
Specifies the transfer direction.
The valid values are as follows:
- S: sends a file.
- R: receives a file.
- C: sends a command.
|
None
|
Yes
|
|
TruncateFlag
|
Specifies whether to truncate information.
The valid values are as follows:
|
None
|
Yes
|
| TryMaxCount
|
Specifies the maximum number of transfer retries allowed.
|
None
|
No
|
| UnixPermissions
|
Specifies the UNIX permissions.
When a file is created on a UNIX system, TIBCO MFT Platform Server can set the UNIX permissions on the file.
The UNIX permissions are defined by a three digit number, such as
777, which is the same as for the
chmod command.
|
None
|
No
|
| UserData
|
Specifies the user data, with any alpha, numeric, or national characters.
This parameter is up to 25 characters that will be logged into the history files that contain information that describes the transfer on the local and remote system.
|
None
|
No
|
| WaitFlag
|
Specifies whether to wait for completion.
This parameter will show the status of the transfer after execution.
The valid values are as follows:
- Y: waits for completion.
- N: not wait.
|
None
|
No
|
| zOSAllocDir
|
Specifies the number of directory blocks to allocate.
This parameter is only used when the initiator is z/OS.
|
None
|
No
|
| zOSAllocPri
|
Specifies the primary allocation value in the unit defined by the
zOSAllocType parameter.
This parameter is only used for transferring files to a z/OS system.
The valid values are any numeric.
|
None
|
No
|
| zOSAllocSec
|
Specifies the secondary allocation value in the unit defined by the
zOSAllocType parameter.
This parameter is only used for transferring files to a z/OS system.
The valid values are any numeric.
|
None
|
No
|
| zOSAllocType
|
Specifies the allocation type to be used when transferring files to a z/OS system.
The valid values are as follows:
- T: tracks
- B: tlocks
- C: cylinders
- K: kilobytes
- M: megabytes
|
None
|
No
|
| zOSBlockSize
|
Specifies the block size to be used for file being transferred to a z/OS system.
The valid values are any numeric.
|
None
|
No
|
| zOSDataClass
|
Specifies the valid data class used when transferring files to a z/OS system.
The values are 1 to 8 character data class names defined by your storage administrator.
|
None
|
No
|
| zOSLRECL
|
Specifies the logical record length for files being transferred to a z/OS system.
The valid values are any numeric.
|
None
|
No
|
| zOSMgtClass
|
Specifies the valid management class used when transferring files to a z/OS system.
The valid values are 1 to 8 character management class names defined by your storage administrator.
|
None
|
No
|
| zOSRECFM
|
Specifies the record format to be used when transferring to a z/OS system.
The valid values are as follows:
- F: fixed
- FB: fixed block
- V: variable
- VB: variable blocked
- U: undefined
|
None
|
No
|
| zOSStorClass
|
Specifies the valid storage class used when transferring files to a z/OS system.
The valid values are 1 to 8 character storage class names defined by your storage administrator.
|
None
|
No
|
| zOSUnit
|
Specifies the device type for a file being transferred to a z/OS system.
The valid values are any device types defined to your z/OS system.
|
None
|
No
|
| zOSVolume
|
Specifies the volume serial number for transferring files to a z/OS system.
The valid values are any 1 to 6 character volume serial numbers on your z/OS system.
|
None
|
No
|
