Contents
This sample uses a Sequence operator to generate unique ID numbers for generic product orders, allowing for easy querying
when updating orders. The Orders input stream contains the fields name
, productNum
, quantity
, and price
. The OrdersChanges
input stream contains the same fields plus an orderID
field.
-
In the Package Explorer, double-click to open the
Sequence.sbapp
application. Make sure the application is the currently active tab in the EventFlow Editor. -
Click the Run button. This opens the SB Test/Debug perspective and starts the application.
-
In the Manual Input view, select the Orders input stream.
-
Enter
G Washington
,12345678
,1000
, and4.30
in the name, productNum, quantity, and price fields, respectively. -
Click
and observe that this order has been assigned a field orderID of 1. -
In the Manual Input view, select the OrderChanges input stream.
-
Enter
1
and1350
in the orderID and quantity fields, respectively. -
In the Application Output view, note that the quantity of the previously entered order has been updated.
-
Reselect the Orders input stream.
-
Enter
G Washington
,23456789
,900
, and12.50
in the name, productNum, quantity, and price fields, respectively. -
Click
and observe that this order has been assigned a field orderID of 2. -
Reselect the OrderChanges input stream.
-
Enter
2
,98765432
, and1900
in the orderID, productNum, and quantity fields, respectively. -
Click
and observe that the second order input has been updated. -
When done, press F9 or click the Stop Running Application button.
This section describes how to run the sample in UNIX terminal windows or Windows command prompt windows. On Windows, be sure to use the StreamBase Command Prompt from the Start menu as described in the Test/Debug Guide, not the default command prompt.
-
Open terminal windows on UNIX, or four StreamBase Command Prompts on Windows. In each window, navigate to the directory where the sample is installed, or to your workspace copy of the sample, as described above.
-
In window 1, type:
sbd Sequence.sbapp
The window shows
notice[StreamBaseServer] listening on port 10000
-
In window 2: type:
sbc dequeue OutputOrders
No output is displayed at this point, but the dequeuer is prepared to receive output. This window will eventually show the output of the application.
-
In window 3, type:
sbc enqueue OrderChanges
The sbc command is now awaiting keyboard input.
-
In window 4, type:
sbc enqueue Orders
The sbc command is now awaiting keyboard input. Then type:
G Washington, 12345678, 1200, 4.30
Observe this line in the dequeue window:
G Washington,12345678,1200,4.3,1,null,null,null,null
. Notice that this order has been assigned an orderID of 1 in the fifth field. (The null values at the end mean that this is a new order.) -
In window 3, type:
1,null,null,1350,null
Observe this line in the dequeue window:
G Washington,12345678,1350,4.3,1,G Washington,12345678,1200,4.3
The first set of values are the new order values and the second set of values (that were null before) show the old values.
-
In window 4, type:
G Washington, 23456789, 900, 12.50
Observe this line in the dequeue window:
G Washington,23456789,900,12.5,2,null,null,null,null
-
In window 3, type:
2, null, 98765432, 1900, null
Observe this line in the dequeue window:
G Washington,98765432,1900,12.5,2,G Washington,23456789,900,12.5
-
In window 3 and 4 type Ctrl+C to stop the sbc commands.
-
In window 3 or 4, type the following command to terminate the server and dequeuer:
sbadmin shutdown
In StreamBase Studio, import this sample with the following steps:
-
From the top menu, click
→ . -
Select operator from the Data Constructs and Operators category.
-
Click OK.
StreamBase Studio creates a single project for all the operator samples.
When you load the sample into StreamBase Studio, Studio copies the sample project's files to your Studio workspace, which is normally part of your home directory, with full access rights.
Important
Load this sample in StreamBase Studio, and thereafter use the Studio workspace copy of the sample to run and test it, even when running from the command prompt.
Using the workspace copy of the sample avoids the permission problems that can occur when trying to work with the initially installed location of the sample. The default workspace location for this sample is:
studio-workspace
/sample_operator
See Default Installation Directories for the location of studio-workspace
on your system.
In the default TIBCO StreamBase installation, this sample's files are initially installed in:
streambase-install-dir
/sample/operator
See Default Installation Directories for the default location of studio-workspace
on your system.