• Important Information
• TIBCO Documentation and Support Services
• Introduction
  • Product Overview
    • Models
  • Appliance Components
• Installation
  • Installation Requirements
  • Installing the Hardware
    • Unpacking the Equipment
    • Installing the Rack Kit
    • Grounding the Appliance
    • Preventing Electrostatic Discharge Damage
    • Connecting the Power Supply to an AC Power Source
    • Verifying LED Operation
    • Connecting Two TIBCO Enterprise Message Service Appliances
    • Connecting the Appliance Management Port to the Network
    • Connecting the Appliance to Your Network
      • Uplink Configuration
    • Connecting Directly to the Appliance for Initial Setup
  • Initializing the Software
    • Accessing the Appliance System
    • Configuring the Management Information
    • Restarting the Software Initialization Process
    • Configuring Appliance Users
    • Re-configuring Management Information
    • Configuring Host Information
    • Configuring EMS Server Information
    • Configuring Fault Tolerant Behavior
    • Configuring Disaster Recovery
    • Beginning Appliance Operations
• Configuration
  • Predefined Appliance User Accounts
    • Working with the File Transfer Directory
  • TIBCO Enterprise Message Service Server States
  • Appliance Monitoring
  • TIBCO Enterprise Message Service™ Instances
    • Maximum Connections
    • Configuration
  • Single Appliance Configuration
  • Fault Tolerant Configuration
    • Configuration Changes on Fault-Tolerant Servers
    • Authorization and Fault-Tolerant Servers
    • Startup Process
    • Failover Process
    • Restoring After a Failover
    • Failover Events
  • Disaster Recovery Configuration
    • Disaster Recovery Process
    • Enabling Disaster Recovery
      • Initial Setup
      • Verify that the EMS Server Instance on Each Appliance is Operational
      • Establish Communications Between the Quad Appliances
      • Activate Disaster Recovery Support
    • Rejoining the Quad
      • DR Members
      • DR Leader
    • Recovering to a Backup Site
    • Restoring the Production Site
  • Encrypted Data Store (EDS) Configuration
    • Configuring the Encrypted Data Store on EMS Appliance
    • Disaster Recovery
• Commands
  • CLI Overview
    • Using the CLI to Make Configuration Changes
  • Command Overview
  • General Commands
    • date
    • diagnostics-enable
    • eds-key-refresh
    • ems-gateway
    • exit
    • export
    • export-support-logs
    • forcestart
    • halt
    • help
    • import
    • info
    • initialization-progress
    • log-show
    • log-test
    • quit
    • reboot
    • restore-primary-active
    • services
    • setup-enable
    • setup-show
    • show
    • start
    • stop
    • upgrade-software
    • version-show
  • Disaster Recovery Commands
    • dr-activate
    • dr-recover
    • dr-restore
    • key-accept
    • key-join
    • key-reset
  • Configuration Setup Commands
    • config-apply
    • config-pending
    • config-revert-pending
    • config-revert-unsaved
    • config-review
    • config-save
    • dr-config
    • eds-config
    • ems-config
    • ft-config
    • health-check-config
    • hostinfo-config
    • initial-config
    • mgmt-config
    • set-timezone
    • syslog-config
  • Instance Management Commands
    • call-tibemsadmin
    • forcestart-instance
    • start-instance
    • stop-instance
    • switch-active
  • Diagnostics and Troubleshooting Commands
    • disk-check
    • dr-check
    • log-audit
    • log-remove
    • log-rotate
    • log-truncate
    • network-check
    • peer-login
    • port-disable
    • port-enable
    • port-show
    • pstack-instance
    • remove-certs
    • remove-cores
    • remove-snapshots
    • remove-transfers
    • reset-all
    • session-timeout
    • uplink-config
    • zone-admin